Arctic-Freeze Kit
Arctic Freeze™ (-109 Degrees F) C02 Pipe Freezing System
Instruction Manual
Use a recharge kit with a sealant to repair small leaks. You can spend more than $1,000 trying to find and repair a small leak, so it’s often better to use a product that contains a sealant. This will help your system hold its recharge longer, as the refrigerant won’t leak out as quickly. See how easy it is to recharge your car's air conditioning system with Arctic Freeze Ultra Synthetic R134a! Attach the charging hose/gauge assembly. Once needle makes it anywhere in green zone of the gauge, charging is complete. Do not try to get it to the highest part of the green zone or you risk overcharging. Remove hose from service port and replace plastic cap when finished. Store any unused refrigerant in a cool, dry place, with charging hose securely attached to can. Save on Interdynamics Arctic Freeze Ultra Synthetic R-134a Recharge Kit with UV Dye and Oil AFK-11CS at Advance Auto Parts. Buy online, pick up in-store in 30 minutes. R134a Recharge kit with reusable trigger dispenser, refrigerant, leak seal and UV Dye for leak detection. Includes: Replaces lost refrigerant and oil to AC system and is formulated with advanced QwikBoost chemistry.
Getting Started
1. After selecting the proper size jacket, read the instructions on the jacket label carefully. Remember to take your time - do not try to rush a freeze.
2. Make sure that you have enough C02 on hand to complete the freeze. See table on back for estimated amount of C02 required for different pipe sizes. Always have more than enough to complete the freeze.
3. Be sure there is no flow of water through the pipe.
4. Keep torch flame at least 14' or more from end of jacket and place jacket 24' or more away from a closed connection.
Beginning the Freeze
1. Open valve on cylinder fully and inject liquid C02. (Injection time, waiting time, and approximate total time is printed on the jacket label). The chart on the back also gives the approximate injection waiting and total time required for different pipe sizes.
2. During the freezing period, squeeze the jacket against the pipe to evenly distribute the C02. Wear gloves.
3. Note that the injection waiting and total time required is based on pipes containing cold water under 70 degrees F. It is important to fill the space between the pipe and jacket with a solid ball of 'dry ice'. If upon completing the recommended injection and waiting times you squeeze the jacket and the space is not completely filled, proceed with additional injection/waiting times until 'white frost rings' appear at either end of jacket and a solid ball of 'dry ice' has formed around pipe. Caution - do not attempt to rush a freeze.
Proceeding with the work
When 'white frost rings' have formed at each end of jacket, the 'ice-plug' inside the pipe has formed, and the work can be carried out.
Additional Injections
About every 15 minutes make additional injections of C02 for 20-30 seconds to maintain a solid ball of 'dry-ice' around pipe. This procedure will allow you to maintain the 'freeze' until the work is completed.
Arctic Freeze Recharge Kit Instructions Download
Upon Completion of Work
When the work is completed, remove the jacket and allow the pipe to thaw naturally. Do not apply heat! The 'ice-plug' will melt and the flow will return to normal in about 10 minutes.
C02 Cylinder
The 20 lb. cylinder weighs about 26 lbs. empty and 46 lbs. full. When full, it contains 18 lbs. of usable C02 and 2 lbs. of residual gas. The residual gas cannot be used for freezing. Always weigh the C02 cylinder before attempting to freeze to make sure that a sufficient amount is available. We recommend always having an extra tank of C02 on hand.
Safety Precautions
Always use C02 in a well ventilated area as C02 is heavier than air.
Freezing table Cold water / Metal pipes (Under 70 Degrees F)
Important
Read all of the instructions carefully before beginning a freeze. The above information is provided as an estimate. Individual conditions will change: injection time, waiting time, and total time required. Do not over inject C02 which will cause too much dry ice to form in the space between the jacket and the pipe and possibly damage the jacket. A siphon or bottom dip tube must be installed in C02 cylinder in order to get a freeze.
3' and 4' Pipe Sizes
Read instructions carefully - have plenty of C02 available. Contact our office if you have any questions - 800-327-3552 / FAX 630-377-0274.
Trouble Shooting - Not Obtaining a Freeze
1. There is a flow of water in pipe.
A freeze will not take place if there is a significant flow of water. If a small amount of water movement is taking place, place two jackets end to end so that they touch and begin the freezing process again. Inject C02 to both jackets.
Arctic Freeze Recharge Kit Instructions Diagram
2. The C02 cylinder is empty. No dry ice will form around the pipe. If a solid ball of dry ice has not formed around the pipe, the tank is empty. Replace immediately.
3. Insufficient time has been allowed for the ice-plug to form. Start the freezing process over again from the beginning. Make sure that you have sufficient amount of C02.
Safety Precautions
1. Use Arctic-Freeze only in well ventilated areas. C02 is heavier than air and care should be taken to disperse X02 in confined and low lying areas.
2. Because solid C02 is very cold (-109 degrees F) it can cause a burn or frostbite to the bare skin. Always wear protective gloves when using pipe freezing equipment. Keep out of the reach of children.
3. Store C02 cylinders in a cool place. Do not expose to any temperature over 120 degrees F.
4. Before beginning a freeze, check all of the equipment and replace any items that are damaged.
Summary
Arctic-Freeze is easy to use. Read the instructions carefully and keep in mind that the freezing table is based on cold water - in metal pipes - under 70 degrees F. Higher water temperatures will require longer! Injection, waiting, and total time required for each pipe size. Also, the consumption of C02 will increase.
Always have more than enough C02 available to complete the freeze safely.
Do not attempt to freeze hot water
Do not hesitate to contact our office to discuss any questions that you have about a specific pipe freezing application.